Batteries-Chargers-2024-EN

» 3-part charging characteristic IUoU » High efficiency » Multiple outputs for independent charging of multiple batteries or battery banks » Adjustable for open or closed batteries » Built-in output fuse » Delivery of full power at low AC mains voltage » Output with low ripple » Power factor cosψ =1 » compatible with generators » short-circuit, overload, overvoltage and overheating protected » can be used in a wide temperature range, -15°C to +70°C, reduced charging capacity first from +45°C room temperature ! with safety plugs on models 140 and 250 ! 230 V plug and charging cable set are not included Q uick SBC NRG+ battery chargers The new SBC NRG+ chargers are more compact and equipped with connectors that make connection easy and practical. Thanks to their efficiency (up to 92%), they offer much lower consumption, lower heat dissipation and greater system reliability. All models have multiple charging outputs and the charging current is distributed using MOSFET technology, with virtually no voltage loss and therefore no additional energy requirement. The charging process can be adapted to the battery type: AGM, lead/acid, gel, lithium-ion and Optima batteries. Optional charging cable sets Order Nr. only for Mod. 140 + 365, 1.5m, 6mm² , with pole clamps 99 1061 for all LOW POWER models, with Quick-Power terminals 99 1059 C harging cable sets for Q uick SBC chargers included SBC NRG+ LOW Power SBC NRG+ MEDIUM Power Size LxWxH: 170x391x82 mm Size LxWxH: 170x481x82 mm SBC NRG+ HI Power Sicherheitsklassifizierung EN 60335-2-29 EMV-Klasse EN 55022/A FCC TITEL 47 TEIL 15 ABSCHNITT B KLASSE A Model Volt Nominal charging power LxWxH mm Weight Outputs Order Nr. 140 12 V 12 Ah 114x187x71 1,1 kg 2 56 7550 250 12 V 25 Ah 114x252x71 1,6 kg 3 56 7551 300 12 V 30 Ah 114x252x71 1,6 kg 3 56 7552 500 12 V 40 Ah 114x276x71 1,8 kg 3 56 7554 365 24 V 15 Ah 114x252x71 1,6 kg 3 56 7553 Model Volt Nominal charging power Weight Outputs with RDS without RDS 700 12 V 60 Ah 3,1 kg 3 56 7559 56 7558 950 24 V 40 Ah 3,1 kg 3 56 7563 56 7562 Model Volt Nominal charging power Weight Outputs with RDS without RDS 1100 12 V 80 Ah 3,1 kg 3 56 7568 56 7564 1200 12 V 100 Ah 3,1 kg 3 56 7565 56 6338 1450 24 V 60 Ah 3,1 kg 3 56 7567 56 7566 1950 24 V 80 Ah 3,1 kg 3 56 7569 56 6329 2450 24 V 100 Ah 3,1 kg 3 56 6326 56 7571 Errors and technical changes reserved Setting battery type End voltage Maintenance voltage Lead / acid open 14,1 V / 28,2 V 13,4 V / 26,8 V Lithium ion** 14,2 V / 28,4 V 13,5 V / 27,0 V Lead / acid closed 14,4 V / 28,8 V 13,8 V / 27,6 V AGM 14,4 V / 28,8 V 13,6 V / 27,2 V Gel 14,4 V / 28,8 V 13,8 V / 27,6 V Optima 14,7 V / 29,4 V 13,8 V / 27,6 V **Due to the diversity of lithium batteries, our Quick chargers can only be used for those who need the charging end and maintenance voltage specified in the table above according to the manufacturer. In case of doubt, please contact the battery manufacturer! RDS 1562 Remote control and control panel for QUICK SBC NRG+ chargers Medium and Hi-Power. Simultaneously displays the voltage of all 3 battery groups, the charging state/phase of the charger, the current charging current and any error messages. In addition, this panel can be used to make various settings for the charger, such as the level of trickle charge for full batteries, which is usually higher when the boat is in use with ice boxes running and lighting than with an unused boat. This prevents unnecessary restarts of loading cycles. The connection between the charger and the control panel is via a CAN bus line and is connected to the RJ45 socket of the charger. The scope of delivery also includes two end terminals for the CAN bus line. RDS 1562 as retrofit kit 56 6266 KTB4N interface for battery temperature sensors The QUICK SBC NRG+ Medium and Hi-Power chargers each come with a temperature sensor. This is connected to the RJ11 socket on the charger. However, if the temperature of several battery banks is to be monitored in order to optimize the charging process, this interface is required, which is integrated into the CAN bus line. As soon as this is in the network, the RJ11 input of the charger is switched off and the tempe- rature data is only supplied via the CAN bus line. A self-adhesive KTBS temperature sensor is included with the interface. Further sensors are optionally available. Up to 4 temperature sensors can be connected to one interface, but several interfaces can be integrated into the network so that a greater number than 4 batteries can be measured simultaneously. KTB4N interface 56 6273 KTBS additional temperature sensors 56 6274 CHARGERS 7